about-us1 (1)


Super heavy duty 6f22 PP3 zinc carbon 9v battery

Short Description:

The nine-volt PP3-size battery is commonly available in primary zinc-carbon Designations for this format include NEDA 1604 and IEC 6F22 (for zinc-carbon) or MN1604 6LR61 (for alkaline). The size, regardless of chemistry, is commonly designated PP3—a designation originally reserved solely for carbon-zinc, or in some countries, E or E-block.[3] A range of PP batteries was produced in the past, with voltages of 4.5, 6, and 9 volts and different capacities; the larger 9-volt PP6, PP7, and PP9 are still available. A few other 9-volt battery sizes are available: A10 and A29.

Product Detail

Product Tags


Carbon Zinc 9V 6F22 Battery (2)
Carbon Zinc 9V 6F22 Battery (3)


This specification governs the technical requirements of Sunmol Carbon Zinc battery of 6F22. If it doesn’t list the other detailed requirements, the technical requirements and dimensions of battery should meet or above GB/T8897.1-2008 and GB /T8897.2-2013.

1.1Reference Document

GB/T8897.1 (IEC60086-1,MOD)(Primary Battery Part 1: General)

GB/T8897.2 (IEC60086-2,MOD)(Primary Battery Part 2: Dimensions and Technical Requirements)

GB8897.5 (IEC 60086-5,MOD)(Primary Battery Part 5: aqueous electrolyte battery safety requirements)

1.2Environmental protection standard

The battery accord with 2006/66/EC

Chemical system, Voltage and Designation

Electrochemical system: zinc - manganese dioxide (ammonium chloride electrolyte  solution), does not contain mercury

Nominal voltage: 1.5V

Naming: IEC: 6F22    JIS: 006P  

Battery Size

Conform to the requirements of the brief

3.1 Acceptance tool

Using vernier caliper measurement precision is not less than 0.02 mm, measure to prevent the battery short circuit, one end of the caliper head card should be labeled as a layer of insulating materials。

3.2 Acceptance methods

The GB2828.1-2003 normal inspection sampling plan at a time,special inspection level S-3,acceptance quality limit AQL=1.0

4.Weight and discharging capacity

Typical Weight: 36g

discharge capacity:150mAh(load 180Ω, 24h/day, 20±2℃,RH60±15%, final 

voltage 4.8V)

Carbon Zinc 9V 6F22 Battery (4)

Product Features

open-circuit voltage, closed - circuit voltage and short-circuit current



sampling standard

After 2 months, new battery


GB2828.1-2003 Normal inspection sampling plan, special inspection level S-4,AQL=1.0

After 12 months at

room temperature


Test conditions

load resistance 3.9Ω, measuring time 0.3 seconds,temperature 20±2℃

Technical Requirements

Discharging Ability


Discharge Conditions


National standard requirement

Shortest Average

Discharging Time

Discharge load

Discharge Time

Cut-off discharge voltage


After 2 months, new battery

After 12 months at

room temperature



5.4 V






5.4 V






4.8 V




Satisfaction Standard:

1. 9 pieces of battery will be tested for each discharging standard;

2. The result of the average discharging time from each discharging standard shall be equal to or more than the average minimum time requirement; no more than one battery has a service output less than 80% of the specified requirement. Then the batch battery performance test qualified.

3. If nine section of the battery discharge average less than the specified value of minimum average discharge time and (or) is less than the specified value of 80% of the battery number more than 1,we should take another 9 batteries to test again and calculate the average. Calculation results conform to the requirement of article 2, the batch battery performance test qualified. If it does not conform to the requirement of article 2, the batch battery performance test is unqualified, and no longer test.

Packaging and Marking

Anti-leakage ability

Discharge Conditions


Acceptance Standard



Discharge load


Discharge Time

Cut-off discharge voltage(V)

at temperature 20±2℃; relative humidity: 60±15% RH




 No leakage recognized by eyes








Safety performance requirements




Acceptance Standard

External short circuit

At temperature 20±2℃,With wires to the battery positive negative switched on 24 hours

No explosion







The following markings will be printed, stamped or impressed on the body of battery:

1. Designation: 6F22

2. Manufacturer or trademark: Sunmol ®

3. Polarity: “+”and“-”

4. Expiration date deadline or manufacturing time

5. The attention notes for safe use.

Cautions for Use

1. Since the battery is not manufactured for recharging, there are risks of electrolyte leakage or causing damage to the device if the battery is charged.

2. The battery shall be installed with its “+” and “-” polarity in a correct position, otherwise may cause short-circuit.

3. Short-circuiting, heating, disposing of into fire or disassembling of battery is prohibited.

4. Battery can not be forced discharged, which leads to excess gassing and may result in bulging, leakage and de-crimping of cap.

5. New batteries and used ones can not be used at the same time. It is recommended to use the same brand when replacing batteries.

6. Electrical appliances should be take out the battery when not in use for a long time

7. Exhausted batteries shall be removed from the compartment in order to prevent over-discharge.

8. Prohibit direct welding battery, otherwise it will damage the battery.

9. Battery are to be kept away from children. If swallowed, contact a physician at once.

Reference Standards

Normal Packing

Every 2 or 3 and 4 batteries or according to customer requirements with transparent membrane after hot shrinkage, each 60 knots in 1 inner boxes, 20 boxes into 1 box.

Storage and shelf life

1. Batteries should be stored in ventilated, cool and dry place.

2. The battery should not be exposed to direct sunlight for a long time or in the rain. 

3. Not to mix removed packaging battery stack together.

4. Stored at condition of tempreture20℃±2℃, relative humidity 60±15%RH, the battery shelf life is 2 years.

Discharge curve

Typical discharge curve

Discharge environment: 20℃±2℃, RH60±15%

With parameter adjustment, product technology updates, technology specification will update at any time, please do not hesitate to contact to stand for the latest version of the specification.

Discharge curve

Normal Packing

Every 2 or 3 and 4 batteries or according to customer requirements with transparent membrane after hot shrinkage, each 60 knots in 1 inner boxes, 20 boxes into 1 box.


Normal Packing


  1. 25 years of experience in dry cell production
  2. Support OEM & ODM service
  3. Moderate MOQ
  4. CE/SGS and MSDS Certifications
  5. Selling in more than 30 countries and regions



Q1: How do you make our business long-term and good relationship?

A:1. We keep good quality and competitive price to ensure our customers benefit ;

2. We respect every customer as our friend and we sincerely do business and make friends with them, no matter where they come from.


Q2.What’s the MOQ?

A:Small quantity is OK for trial order or samples if we have stock,customize brand or customize request please contact us.

Benefits of Alkaline

Alkaline batteries have a higher energy density and a longer shelf life – the time a battery can remain in storage without losing any of its capacity. The Alkaline Battery Technology is one where intensive research and development have led to three unique technologies. The Sunmol Alkaline batteries first of all have an Anti-Leak Protection to prevent damage to appliances. The reason for leakage is the chemistry of the battery that changes and gas that is generated when the battery discharges. 

Next to this, there is also a specially designed coating inside the batteries that reduces contact resistance for greater reliability. Lastly, the Alkaline cells have an Extra Power Formula to maintain power for a longer period in high-drain devices. 



  • Previous:
  • Next:

  • Write your message here and send it to us